×

Registration

Profile Informations

Login Datas

or login

First name is required!
Last name is required!
First name is not valid!
Last name is not valid!
This is not an email address!
Email address is required!
This email is already registered!
Password is required!
Enter a valid password!
Please enter 6 or more characters!
Please enter 16 or less characters!
Passwords are not same!
Terms and Conditions are required!
Email or Password is wrong!

INON Snoot Set for S-2000

Product Code: 456212143583
INON Snoot Set for S-2000

Be the first to review this product

£185.99
OR
Description

Details

Snoot Set for S-2000

Snoot Set for S-2000Set contents: Rubber Hood 52, W40°Filter LE x 2, Snoot Tube 10, Snoot Tube 26

The INON Snoot Set for S-2000 is an accessory for the INON S-2000 to change beam angle. The various combination of packaged parts supports 6 different beam coverage with the following sophisticated effects
●To block extra diffused light eliminating backscatter
●To highlight a subject by illuminating the subject only
●To give a spotlight effect on a subject etc.
The telescopic structure of the Rubber Hood helps to save space for storage.

Various combination for different beam coverage

Various combination for different beam coverage
Various combination of packaged parts provides 6 different beam coverage to suit to a subject and intended effect.

Pattern 1[Pattern 1]
Rubber Hood 52
(when collapsed)

[coverage]
approx. 105° (horizontal)
approx. 95° (vertical)

To block extra diffused light eliminating backscatter

Pattern 2[Pattern 2]
Rubber Hood 52
(when extended)

[coverage]
approx. 65° (horizontal)
approx. 60° (vertical)

Pattern 3[Pattern 3]
Rubber Hood 52
(when extended)
+Snoot Tube 26
+W 40° filter LE

[coverage]
approx. 26° (horizontal)
approx. 24° (vertical)

Pattern 4[Pattern 4]
Rubber Hood 52
(when extended)
+Snoot Tube 26


[coverage]
approx. 31° (horizontal)
approx. 19° (vertical)

Pattern 5[Pattern 5]
Rubber Hood 52
(when extended)
Snoot Tube 10
+W 40° filter LE

[coverage]
approx. 16° (horizontal)
approx. 12° (vertical)

Pattern 6[Pattern 6]
Rubber Hood 52
(when extended)
+Snoot Tube 10


[coverage]
approx. 22° (horizontal)
approx. 9° (vertical)

*Beam coverage is actual measured data by INON INC and could have variant depending on test condition.

*Always conduct test shots to familiar with the product characteristic before you take an important shot. When using the S-2000 in S-TTL Auto mode for spotlight effect of this product, center spot metering mode on a camera is recommended since average metering mode or multi pattern metering mode could wash out the center of an image. In case S-TTL Auto mode does not provide appropriate exposure, use Manual mode.

*Make sure to cool down the "S-2000" according to instruction manual / [Compatible battery, operational limitation on flashing] leaflet provided with the S-2000, to prevent overheating / degradation of light emitting part / inner components. The light emitting part could have discoloration or burn when excessive repeated flashes are made. Should you observe any irregularity mentioned above, stop using the strobe immediately.

*"Slave D Holder Unit 3" of the "Optical D Slave Cable 3 Type L" is not compatible with this product.

*When you entry with this product being attached on a strobe, make sure to evacuate remaining air inside of the Rubber Hood before you get underwater.

*Always extend the "Rubber Hood 52" when using the "Snoot Tube 10" or "Snoot Tube 26" together to prevent possible damage on light emitting part and/or inner circuit of the S-2000 etc. since generated heat could stay close to the light emitting part.

Additional Information

Additional Information

manufacturer INON
MPN 456212143583
Image Gallery N/A
Reviews
Tags

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.